How to use these fluid mechanics viva questions
A viva tests more than whether you can recall an equation. You need to identify the physical model, state the assumptions, use consistent quantities and explain what the result means. A strong answer is usually easier to follow when you speak through those steps in order.
The stations below are practice scenarios, not a claim about the format or marking rules of any particular institution. Fluid mechanics assessments vary, so check your course or examining body's guidance for the topics and format you are expected to cover. For each station, answer the opening question aloud before reading the model response. Aim to explain your reasoning, not just give the final number.
In MySummaries, an examiner strip for a fluid mechanics practice set can make the feedback focus visible before you begin:
The emphases here are a practice framework, not a universal institutional rubric. Use them as a check that your answer connects equations to the actual flow situation. If your course specifies different expectations, use those instead.
A repeatable method for a technical viva
Use this sequence whenever a question involves a calculation or physical explanation:
- Clarify the system. Identify the fluid, geometry, flow direction and the points or surfaces being compared. Ask a brief clarifying question if a necessary condition is missing.
- State the model and assumptions. For example: steady incompressible flow, a full circular pipe, negligible change in elevation, or a smooth flat plate with zero pressure gradient. Do not silently apply an equation outside its assumptions.
- Name the governing relation. State the equation before substituting values. Define symbols that could be ambiguous, especially pressure (gauge or absolute) and friction factor (Darcy or Fanning).
- Work through units and arithmetic. Keep intermediate values visible. A sensible estimate can expose an arithmetic or unit error.
- Interpret and qualify. Say what the result means and what could change it. For a head-loss calculation, for example, explain how a change in pipe diameter or roughness affects the loss.
If you do not know a value, state what information you need and how it enters the analysis. Guessing a number without identifying its source makes it hard to distinguish a knowledge gap from an unsupported assumption.
A station list helps turn a syllabus into practice prompts. These are four possible stations drawn from common fluid mechanics topics; the final row is included as an unattempted prompt to return to later:
The three worked stations below show how to turn that opening prompt into a complete spoken answer. Each has a short target time for practice, followed by criteria, feedback and a model response. The scores represent developing practice attempts, not a pass mark.
Station 1: Flow in a straight pipe
Start by establishing which friction-factor convention is being used. The question gives the Darcy friction factor, so use Darcy–Weisbach directly; the Fanning friction factor is one quarter of the Darcy factor. For a full circular pipe, calculate mean velocity from flow rate divided by cross-sectional area, then calculate Reynolds number to check whether the stated friction factor is plausible for the flow regime.
A complete answer should not imply that the friction head is the entire pump head requirement. Fittings, valves, entrance and exit losses, elevation change and any required outlet pressure would need separate treatment if they were part of the system.
The recorded response and practice feedback for this station look like this:
Examiner
Water flows through a 50 mm diameter, 30 m long pipe at 0.003 m³/s. With Darcy friction factor 0.025, estimate the friction head loss and explain your assumptions.
Uses Darcy–Weisbach for steady, full-pipe flow and treats the given friction factor as Darcy, but does not initially state that minor losses are excluded.
ImproveSay explicitly that the estimate covers straight-pipe friction only, with steady incompressible flow and constant diameter.
Gets the area and mean velocity close to 1.53 m/s and identifies the flow as turbulent, but omits the Reynolds-number calculation.
ImproveShow Re = ρVD/μ; for water near 20°C this is about 7.6 × 10⁴.
Obtains a friction head close to 1.8 m and uses metres of fluid, with a small rounding slip in the intermediate velocity head.
ImproveKeep v²/(2g) as a separate step: approximately 0.119 m, then multiply by fL/D = 15.
Explains that the pipe dissipates mechanical energy but does not distinguish this from total system head.
ImproveState that fittings, elevation and pressure requirements are additional terms if the question concerns pump duty.
A strong answerAssuming steady, incompressible flow in a full, constant-diameter pipe, the mean velocity is Q/A. The area is π(0.05²)/4 = 1.96 × 10⁻³ m², so V is about 1.53 m/s. For water near 20°C, Re = ρVD/μ is about 7.6 × 10⁴, consistent with turbulent flow. Using the stated Darcy factor, Darcy–Weisbach gives h_f = f(L/D)(V²/2g) = 0.025(30/0.05)(1.53²/2g), or about 1.8 m of water. This is the straight-pipe friction loss only; fittings, elevation and required pressure are not included.
That is a MySummaries station, filled with fluid mechanics material. Yours is written from your own notes. Start free
Notice the order: assumptions, velocity, regime check, head loss and limitation. Practise saying each step without rushing the equation. If a value seems implausible, check the units and the area calculation before changing the physical model.
One common follow-up is: “What happens to the friction loss if the diameter is reduced?” Do not answer only that it increases. At fixed flow rate, reducing diameter increases velocity, and also changes the length-to-diameter ratio and usually the friction factor. The resulting loss can rise sharply; calculate it for the stated conditions rather than relying on one factor alone.
Station 2: Pump suction and cavitation
This station tests whether you can distinguish available net positive suction head from the pump’s required value. NPSH is expressed as a head of liquid. For an open suction tank, a useful form at the pump suction reference is the absolute pressure head at the liquid surface plus the elevation head relative to the pump, minus suction-side losses and the liquid vapour-pressure head. The exact expression depends on the chosen datum and system layout.
Do not compare gauge pressure directly with vapour pressure: vapour pressure is an absolute pressure. Also, do not assume that a pump can safely operate just because the available value is numerically equal to the manufacturer’s required value. The required information and operating margin should be checked against the pump documentation and the system conditions.
A practice response might be marked as follows:
Examiner
A pump draws water from an open tank. Explain how you would assess cavitation risk and what operational changes could reduce it.
Connects cavitation to local pressure reaching vapour pressure, but does not clearly distinguish vapour formation from bubble collapse downstream.
ImproveExplain that vapour cavities form in low-pressure regions and collapse when carried into higher-pressure regions, causing noise, vibration and possible damage.
Names NPSHa and NPSHr, but initially compares them without stating that pressure terms must be absolute.
ImproveDefine NPSHa at the pump suction relative to vapour pressure and compare it with the manufacturer’s NPSHr at the actual operating flow.
Mentions suction-line losses and tank level but leaves out liquid temperature and vapour pressure.
ImproveInclude suction lift, pipe and fitting losses, surface pressure, elevation and the liquid’s temperature-dependent vapour pressure.
Suggests reducing suction losses, but does not connect each remedy to increasing NPSHa.
ImproveRelate remedies to the energy balance: reduce line losses, lower pump elevation or increase suction pressure where the system allows.
A strong answerCavitation occurs when local absolute pressure falls to the liquid’s vapour pressure, forming vapour cavities that can collapse in higher-pressure regions. I would calculate available NPSH at the pump suction using absolute pressure, the liquid level relative to the pump, suction-line and fitting losses, and the vapour-pressure head at the operating temperature. I would compare NPSHa with the manufacturer’s NPSHr for the actual flow and operating condition, allowing an appropriate margin rather than assuming equality is safe. To increase NPSHa, I could reduce suction-pipe losses, avoid unnecessary fittings, increase the liquid level or reduce the pump’s elevation where feasible. I would also check whether a higher liquid temperature or a change in flow is increasing the risk.
For a follow-up, organise remedies by what they change. A larger or shorter suction line can reduce friction losses; fewer restrictive fittings can reduce local losses; a lower pump position can reduce suction lift; and reducing liquid temperature lowers vapour pressure. Any proposed change must still fit the equipment limits and process requirements. If the data are not provided, describe the comparison you would make rather than inventing an NPSH number.
Station 3: Boundary-layer separation
This question is about the relationship between pressure change and momentum near a wall. In an adverse pressure gradient, pressure increases in the direction of the flow. Fluid close to the wall has already lost momentum through viscous effects, so it can be unable to move against that pressure rise. The boundary layer thickens and may separate from the surface.
The idealised separation condition is zero wall shear stress, or zero velocity gradient normal to the wall at the wall: τw = μ(∂u/∂y)wall = 0. Downstream of separation, reversed near-wall flow may occur. Avoid saying that separation simply happens whenever velocity decreases; explain the pressure gradient and the near-wall momentum deficit.
A third spoken attempt can be reviewed this way:
Examiner
Explain how an adverse pressure gradient can cause separation, and describe the condition at the wall at the point of separation.
Correctly states that static pressure rises downstream, but could relate that rise to deceleration of the outer flow.
ImproveAdd that the pressure gradient opposes the flow and the outer-flow speed generally decreases along the surface.
Notes that near-wall fluid has less momentum, but gives only a brief account of viscous slowing.
ImproveExplain that viscosity has already reduced near-wall momentum, making that fluid especially vulnerable to the adverse pressure force.
Identifies zero wall shear stress correctly, but does not give its velocity-gradient form.
ImproveState τw = μ(∂u/∂y)wall = 0 at separation for a Newtonian fluid.
Mentions possible reverse flow but does not distinguish the separation point from the downstream separated region.
ImproveSay that reversed near-wall flow can occur downstream; the idealised separation point is where wall shear first becomes zero.
A strong answerAn adverse pressure gradient means that static pressure increases in the direction of the flow. The outer flow decelerates, and the pressure rise acts against the motion of fluid within the boundary layer. Fluid close to the wall has less momentum because of viscous effects, so it is the first region that may fail to move downstream. At the idealised point of separation, wall shear stress is zero: τw = μ(∂u/∂y)wall = 0 for a Newtonian fluid. Downstream, the boundary layer may detach and reversed near-wall flow can develop.
A useful extension is to explain why separation matters. It can increase pressure drag and produce an unsteady wake; in a diffuser, separation can reduce pressure recovery. The exact consequence depends on the geometry and operating conditions. If asked how to delay separation, connect your suggestion to the cause: energising the boundary layer, reducing the adverse pressure gradient, or changing the geometry can help, but the best option depends on the application.
Turn feedback into the next practice session
After each attempt, identify one missing mark rather than rewriting the entire answer. Was the gap an equation, an assumption, a unit, a physical explanation or a limitation? Make a short prompt from that gap and answer it again in a later session. For calculations, practise both the spoken explanation and the arithmetic. For conceptual topics, use a sketch if it helps you explain directions of pressure change, velocity or force.
Keep answers proportionate to the question. A numerical question needs a clear calculation and a check on what the result represents. A mechanism question needs a causal chain, not a catalogue of terms. If the examiner interrupts with a follow-up, answer that point directly, then return to the original thread if needed.
How MySummaries helps
Build a fluid mechanics revision board from your own lecture notes, textbook extracts or worked examples. From that board, MySummaries can turn key relations and concepts into spaced-repetition cards, generate written practice, and create recorded oral stations that give feedback on your spoken explanation. Add your course’s own topics and criteria so the practice reflects what you have been taught. Open MySummaries to start from your material.