Start with the material you actually need to learn

Mechanics of Materials becomes manageable when you treat it as a sequence of physical models, not a collection of equations to memorise. For each problem, identify the member and its loading, draw a free-body diagram, choose the relevant model, then check that the result makes physical and dimensional sense.

Before following the plan, collect your course outline, lecture slides, worked examples, problem sheets and any past assessments you are allowed to use. Topic order and notation vary between courses. Use your instructor’s definitions and sign conventions where they differ from the examples here, and check the official course materials for required topics and assessment details.

The plan below runs for four weeks, with four sessions per week. Each session takes about 75 minutes: 10 minutes of retrieval practice, 45 minutes solving problems, 15 minutes checking and correcting, and 5 minutes recording what to revisit. If you have less time, keep the same sequence and shorten the number of problems rather than skipping the correction step.

Set up a working board

Make one revision board for each connected group of topics, or one board with clearly named sections if your course is compact. Put equations beside their assumptions: for example, the flexure formula applies to elastic bending under the relevant beam assumptions, and the torsion relation shown below is for circular shafts. Keep a separate record of sign conventions from your course.

A board on this topic in MySummaries might be organised like this:

Mechanics of Materials Stress, deformation and member loadingStudy
Core models and problem setupStress, deformation and member loading5 sections · 3 columns
Normal stress and axial strain4 due
  • Average normal stress σ = P/A for an axially loaded member with a uniform section.
  • Normal strain ε = δ/L; for linear elastic uniaxial response, σ = Eε.
  • Check units: Pa = N/m²; engineering calculations often use MPa and mm² consistently.
Bending and transverse shear3 due
  • Flexure formula: σ = My/I; use the distance y from the neutral axis and the section’s second moment of area I.
  • For a rectangular section, I = bh³/12 about its centroidal horizontal axis.
  • Beam shear stress: τ = VQ/(It), where Q is the first moment of area of the portion above or below the point.
Axial deformation

For a prismatic bar with constant axial force and area, δ = PL/(AE). For stepped members, calculate each segment’s deformation and add signed changes in length.

Combined loading and checks

Find normal and shear stresses at the point from each load effect, then combine them using the method required by the course. Check equilibrium, sign convention, units and whether the chosen model’s assumptions are satisfied.

Torsion of circular shafts2 due
  • Shear stress: τ = Tr/J; maximum stress occurs at the outer radius c, so τmax = Tc/J.
  • Angle of twist: θ = TL/(JG) for a uniform circular shaft with constant torque.
  • For a solid circular shaft, J = πd⁴/32; for a hollow shaft, J = π(do⁴ − di⁴)/32.

The board is a map, not a replacement for solving. For every section, keep at least one complete worked example showing the free-body diagram, substitutions and units. When you get an answer wrong, record the cause: missed load, wrong section property, sign error, unit conversion or an assumption used outside its range.

Week 1: establish the foundations

Session 1 — Diagnostic and setup (75 minutes). Choose three representative problems from your course materials: one axial member, one beam reaction problem and one shaft problem. Attempt them without notes for 30 minutes. Spend the rest checking the solutions and sorting each error into a category. Do not use the score as a judgement of ability; it tells you what needs practice first.

Session 2 — Equilibrium and internal resultants (75 minutes). Practise support reactions and free-body diagrams. For each beam or member, cut through a chosen section and find the internal normal force N, shear force V, bending moment M and, where relevant, torque T. Sketch shear-force and bending-moment diagrams from the sign convention used in your course.

Session 3 — Stress, strain and axial deformation (75 minutes). Solve problems involving P/A, σ = Eε and δ = PL/(AE). Include stepped bars and changes in material or area if they are on your syllabus. State the assumptions before calculating: axial loading, small deformation, and linear elastic behaviour where those apply.

Session 4 — Retrieval and repair (75 minutes). Rework two problems from Sessions 2 and 3 with the notes closed. Then explain aloud why the equations fit the problems. Put any equation you could not reconstruct onto your board and make a short question from it for later review.

Week 2: build confidence with beams and shafts

Session 1 — Section properties (75 minutes). Calculate centroid locations and second moments of area for the shapes in your course. Practise composite sections by splitting them into simple shapes and using the parallel-axis theorem, I = Icentroid + Ad². Mark the axis clearly; using the correct shape with the wrong axis is still an error.

Session 2 — Bending stress (75 minutes). Work from a beam’s loading to its bending-moment diagram, then use σ = My/I to find normal stress at specified points. Include the location of maximum tensile and compressive stress. Check that stress is zero at the neutral axis and changes sign across it for ordinary elastic bending.

Session 3 — Beam shear (75 minutes). Practise τ = VQ/(It) on the section types required by your course. Identify the area used in Q and the local thickness or width t at the point. Compare the result’s location with the expected stress distribution for the section; do not substitute a memorised maximum formula without checking its assumptions.

Session 4 — Torsion (75 minutes). Solve circular-shaft problems for torque, maximum shear stress and angle of twist. Use consistent units for T, length, J and G. For shafts joined in series, calculate each segment’s twist and combine the twists with the appropriate signs.

At the end of Week 2, use the due queue to choose what to retrieve first. MySummaries can show the review load by board, so the session starts with a specific topic rather than a general rereading task:

Due today
Axial stress and deformation8 due
Beam bending and shear11 due
Torsion of circular shafts5 due
Combined loadingClear
An illustrative due queue shows which mechanics boards have review cards waiting today.

If a topic has no cards due, use that time for a fresh problem or for checking a derivation against your course notes. A clear queue is not evidence that the topic is mastered; it only means there are no scheduled cards waiting.

Week 3: combine models and practise decisions

Session 1 — Stress transformations or principal stress (75 minutes). If included in your course, practise the required plane-stress method, such as Mohr’s circle or the transformation equations. Label axes, angles and sign convention before reading principal stresses or maximum in-plane shear. If this topic is not on your syllabus, use the session for your next listed topic instead.

Session 2 — Combined loading (75 minutes). Work through members with more than one stress-producing load, such as axial force plus bending or bending plus torsion. Calculate each contribution at the same point before combining. Distinguish normal from shear stress and use a failure criterion only when your course specifies one.

Session 3 — Deflection or energy methods (75 minutes). Select the beam-deflection, strain-energy or other deformation method taught in your course. Practise setting boundary conditions and identifying where a sign, integration constant or compatibility condition enters. Keep one complete derivation beside the final result.

Session 4 — Mixed set under a time limit (75 minutes). Choose problems from at least three sections and work without topic labels. Spend 50 minutes solving, 15 minutes marking against worked solutions and 10 minutes classifying errors. The key skill is selecting a suitable model from the problem statement, rather than recognising an equation after its topic has been supplied.

Use your review data to decide what the next lecture or revision block should cover. The picker below illustrates how a weak area can be prioritised over a section that is already reliable:

New lecture
How long have you got?5 min10 min15 min20 min
Combined loadingBeam shearAxial deformationTorsion

Combined loading · Struggling — repeated errors in selecting the stress components to combine

Generate lecture ideas
An illustrative topic picker flags combined loading as the next short review based on repeated errors.

A ten-minute audio review can be useful between problem sessions, but it should lead back to calculation. After listening, close the notes and solve one short problem that uses the same idea.

Week 4: consolidate and test the whole method

Session 1 — Rebuild the core from memory (75 minutes). On a blank page, write the equations you need for your course, their assumptions and the units of each quantity. Compare with your notes and correct omissions in a different colour. Avoid adding every equation you have ever seen; keep the list aligned to the course outline.

Session 2 — Weakest topic, targeted practice (75 minutes). Choose the lowest-performing section in your error log. Review one worked example, then solve three new problems without copying its steps. For each, write down why the chosen model applies and check the answer against equilibrium, dimensions and limiting behaviour where possible.

Session 3 — Mixed assessment practice (75 minutes). Use a permitted past paper or a set of unseen course problems. Follow the available time limit and conditions for your own assessment, checking official course guidance rather than assuming a format. Mark the work carefully, including method marks if the supplied solution or rubric makes them clear.

Session 4 — Close the loop (75 minutes). Reattempt the problems that previously cost you marks. Finish by selecting the next week’s priorities: unresolved assumptions, repeated calculation errors and topics not yet represented in your practice. Keep a small set of durable cards for facts and equations, but use full problems to practise choosing and applying them.

A weak-area report should direct your next session, not simply rank topics. MySummaries can turn practice results into a view of where marks are being lost and how often each section has appeared in your own question set:

Where marks go missing
48%Combined loading7×
66%Beam shear8×
79%Section properties6×
87%Axial deformation5×
An illustrative weak-area report ranks sections by practice performance and repeat appearances in a question set.

Treat a low percentage as a prompt to inspect the working. If errors cluster around choosing the model, practise classifying problems. If they cluster around arithmetic or units, keep the model fixed and drill the calculation. That distinction makes each repair session more efficient.

How MySummaries helps

For this study plan, MySummaries can turn your own mechanics notes into a revision board, schedule flashcard reviews, and help you identify weak sections from practice. Use it alongside worked problems and your course’s stated requirements, not instead of them.