Start with the problem-solving sequence
Mechanics of Materials connects external loads to internal forces, stresses, strains and deformation. The hard part is often not memorising a formula: it is choosing the right model, using consistent units and interpreting the result correctly.
Course outlines and assessment formats vary. Check your course materials for the topics, notation, sign conventions and permitted formula sheets that apply to you. Then organise your study around a repeatable sequence for solving problems:
- Sketch the member and loading. Show dimensions, supports, loads and the section being analysed.
- Find the internal actions. Use equilibrium to determine axial force, shear force, bending moment and torque at the relevant section.
- Choose a stress or deformation model. State the assumptions, such as linear-elastic behaviour or a prismatic member.
- Calculate with consistent units. In many hand calculations, N and mm are convenient: stress and elastic modulus then use N/mm², equivalent to MPa.
- Check the answer. Check units, sign, scale and whether the result matches the physical behaviour you expect.
Practise each step explicitly. If you jump straight from a diagram to a formula, it can be difficult to spot whether the mistake was in equilibrium, the model or the arithmetic.
Build a board from your course notes
Divide your notes into topics rather than making one large formula sheet. For each topic, capture the conditions under which its equations apply, the quantities needed, and one worked example. Keep a clear distinction between a formula and the reasoning that tells you when to use it.
A useful board gives you a compact view across core topics. This one uses typical mechanics-of-materials relationships; adapt notation and sign conventions to your course.
A board on this topic ends up looking like this:
- Normal stress σ = P/A for a centric load on a uniform section
- For a uniform, linearly elastic bar: δ = PL/(AE)
- Stepped bar: total axial change is the signed sum Σ(PᵢLᵢ/AᵢEᵢ)
- Principal stresses: σavg ± √[((σx − σy)/2)² + τxy²]
- Maximum in-plane shear is the radius of Mohr’s circle
- Use the course sign convention for τxy and the angle of the rotated plane
- Polar second moment for a solid circular shaft: J = πd⁴/32
- Elastic torsion: τ = Tρ/J; maximum at the outside radius c
- Angle of twist: φ = TL/(JG) for a uniform shaft
- Hooke’s law in uniaxial linear elasticity: σ = Eε
- With N and mm, E in N/mm² gives stress in N/mm² = MPa
- For a freely expanding uniform member: δT = αLΔT
- Flexure formula σ = My/I for elastic bending about a principal centroidal axis
- For a simply supported beam with a central point load P: Mmax = PL/4
- Beam shear stress: τ = VQ/(It); for a rectangular section, τmax = 1.5V/A
Work through the board from the load to the response: identify the internal action, calculate the stress distribution, and then calculate deformation if the problem asks for it. Do not treat the board as a substitute for derivations. When a formula is unfamiliar, return to your notes and write down what each symbol represents and the assumptions behind it.
Make a short core checklist
Before starting a longer problem, test whether you can recall the few relationships that organise the topic. This is not a complete formula sheet; it is a prompt to retrieve the governing ideas and then check the detailed equation and assumptions in your notes.
A core checklist for the board is:
Use this as a retrieval exercise: cover the equations in your own notes, write each one from memory, and add the condition that makes it valid. For example, the simple axial deformation expression assumes a uniform member and constant axial force, area and elastic modulus over the length being considered. If any of those vary, divide the member into regions or use the appropriate method from your course.
Practise one-step recall, then full problems
Flashcards are useful for definitions, formula conditions and common distinctions. They are less useful for replacing worked calculations. When you answer a card, say the relationship and its conditions aloud or write them down; then grade how readily you recalled it. Return to difficult cards soon, but also schedule full problems that require you to select and combine methods.
A short drill from this board could look like this:
For a centric axial load on a uniform section, what is the average normal stress?
σ = P/A, where P is the axial force and A is the cross-sectional area.
All 6 cards
That is a MySummaries deck, filled with mechanics of materials material. Yours is written from your own notes. Start free
After the recall drill, choose a problem that makes you decide which equation applies. For an axial member, that might mean first finding reactions and internal force, then calculating stress and extension. For a beam, draw shear-force and bending-moment diagrams before using the flexure formula. For a shaft, separate equilibrium from the torsion calculation. These intermediate steps make your method easier to check and your working easier to review.
Use a deliberate method for worked problems
For each practice problem, write a short line for each decision rather than recording only the final calculation:
- Model: What member, loading and material assumptions are you using?
- Equilibrium: What internal force, moment or torque acts at the section?
- Property: Which area, second moment of area or polar second moment is required?
- Relationship: Which equation applies, and why?
- Result check: Is the unit correct, and is the sign or distribution physically plausible?
For example, if a problem asks for the bending stress at a point, identify the bending moment at the section and the point’s distance from the neutral axis. Check that the section property is the second moment of area about the correct axis. Substituting a value of I about the other axis can give a plausible-looking number that is still wrong.
Keep an error log with three headings: what I did, why it failed, and what I will check next time. Useful entries include mixing N·m with N·mm, using the overall length where only one segment is loaded, omitting a reaction from a free-body diagram, or reporting a maximum stress without identifying where it occurs. Rework a missed problem from a blank page after reviewing the error. Merely rereading a correct solution is not evidence that you can reproduce it.
Turn a weak area into a short lesson
When a topic keeps causing errors, return to the matching section of your own notes. A brief audio explanation can help you hear the sequence of ideas while commuting or between study blocks. It should reinforce, not replace, solving problems with a pencil and checking equations against your course material.
A short lecture can follow the chain from shaft loading to torsional stress and twist:
Transcript · tap any word to jump there
Start with equilibrium. Cut the shaft at the section you need and use the free-body diagram to find the internal torque T. Do not confuse an applied torque on the whole shaft with the internal torque at every section: changes in applied loading can make the internal torque different from one region to another.
For a circular shaft in elastic torsion, shear stress varies with radius: τ = Tρ/J. It is zero at the centre and reaches its maximum at the outside surface, where ρ = c. For a solid circular shaft, J = πd⁴/32. Keep the units together; if torque is in N·mm and dimensions are in mm, the calculated stress is in N/mm², or MPa.
The twist of a uniform shaft segment is φ = TL/(JG), with φ in radians when the inputs use consistent units. A longer shaft twists more; a larger J or shear modulus G reduces the twist. For several segments, calculate the twist in each and combine them with signs according to the direction of rotation. Finish by checking that the result is a rotation, not a stress, and that your section and torque match the region you analysed.
After listening, close the lecture and reproduce its three steps from memory: find internal torque, calculate stress distribution, calculate twist. Then solve a fresh shaft problem without the script. If you cannot explain why the maximum stress occurs at the surface, revisit the relationship τ = Tρ/J and connect the radius to the location in the cross-section.
A weekly loop you can repeat
A practical study block can be 45–60 minutes, adjusted to your timetable. Spend the first few minutes recalling equations and conditions without notes. Use the main part of the block to solve one or two problems, showing diagrams and units. Use the final minutes to mark your work against notes or a worked solution and record one specific correction.
Rotate through axial loading, torsion, beam bending and shear, and stress transformation rather than spending every session on the topic you already find comfortable. Once each topic has had focused practice, include mixed problems: choosing the method is part of the skill. At the end of the week, return to errors and repeat a problem type that previously took several attempts.
If your course includes additional topics, such as combined loading, pressure vessels, failure theories or column stability, add them according to your course outline. Do not assume every course covers the same material or uses the same conventions. Use the official course materials or ask your instructor when a scope or notation detail is unclear.
How MySummaries helps
Build a revision board from your mechanics notes, then use it to generate recall cards, written practice and audio review. Keep the board aligned to your own course outline and use your error log to decide which topic to revisit next. Open MySummaries.