How to use these questions
These questions test foundational structural engineering calculations and mechanics. They are not tied to a particular university course, professional assessment or design code. Work with the assumptions stated in each question; for code-dependent design checks, use the standard specified by your course or project.
Choose an option for each question as it appears, then read the explanation straight away. Pay attention not only to the answer but to the tempting wrong option: spotting the source of a mistake is often more useful than memorising a result. All values use SI units unless stated otherwise.
1. Maximum moment from a central point load
This checks the relationship between a simply supported beam’s span, load and maximum bending moment. A question in the MySummaries practice format looks like this:
A simply supported beam has a 6 m span and carries a single 12 kN point load at midspan. What is the maximum bending moment?
The support reactions are 6 kN each by symmetry. The maximum moment is at midspan: 6 kN × 3 m = 18 kN·m. The strongest distractor is 36 kN·m, which results from using the full 6 m span as the moment arm rather than the 3 m distance from a support to the load.
The useful habit is to find the reactions before calculating the moment. A correct-looking formula cannot rescue an incorrect lever arm.
2. Maximum moment from a full-span UDL
This checks whether you can apply the standard elastic-beam result for a uniformly distributed load over the whole simply supported span.
A simply supported beam spans 5 m and carries a uniformly distributed load of 4 kN/m over its full length. What is its maximum bending moment?
For a full-span UDL, Mmax = wL²/8. Substitution gives 4 × 5²/8 = 12.5 kN·m. The strongest distractor is 25 kN·m, which comes from dividing by 4 instead of 8. The total load is 20 kN, so each support reaction is 10 kN.
Check the units as well as the arithmetic: kN/m multiplied by m² gives kN·m.
3. Fixed-end moment for a cantilever
This checks the effect of a point load at a cantilever’s free end. The question specifies the load location because a load nearer the fixed support would give a different moment.
A 2.5 m cantilever carries an 8 kN point load vertically downwards at its free end. What is the magnitude of the bending moment at the fixed support?
The support moment magnitude is load × perpendicular distance: 8 × 2.5 = 20 kN·m. The strongest distractor is 10 kN·m, which halves the correct result, often by incorrectly treating the member as a simply supported beam with a central load. The cantilever’s fixed support carries the full load moment.
For cantilevers, identify the fixed end and the load’s distance from it before applying equilibrium.
4. Average direct stress
This tests the basic average axial stress calculation, with area expressed in square millimetres.
A member carries an axial tensile force of 300 kN on a cross-sectional area of 6,000 mm². What is the average direct tensile stress?
Stress = force/area. Since 1 N/mm² = 1 MPa, convert 300 kN to 300,000 N: 300,000/6,000 = 50 N/mm² = 50 MPa. The strongest distractor is 180 MPa, which multiplies 300 by 6,000 instead of dividing force by area.
Keep force and area in compatible units before dividing. This calculation gives an average stress; it does not establish that the member is safe under a design code.
5. Axial extension
This checks the elastic extension of a uniform prismatic member. Assume the material is linearly elastic and the load is concentric.
A steel bar is 2,000 mm long, has area 1,000 mm² and carries 100 kN in tension. Take E = 200,000 N/mm². What is its elastic extension?
Use δ = FL/AE. In consistent units, δ = (100,000 × 2,000)/(1,000 × 200,000) = 1 mm. The strongest distractor is 10 mm, which is a factor-of-ten arithmetic or unit-conversion error. The given modulus is already in N/mm², so no conversion from gigapascals is needed.
Writing down the units in the substitution is a quick way to catch a mismatch between metres and millimetres.
6. Ideal Euler buckling load
This checks elastic buckling of an ideal, pin-ended column. The result depends on the stated end condition and assumes a straight, elastic member with an idealised axial load.
An ideal pin-ended column has length 3,000 mm, flexural rigidity EI = 1.6 × 10¹² N·mm², and no intermediate restraint. Using Pcr = π²EI/L², what is its Euler critical load, approximately?
Pcr = π² × 1.6 × 10¹²/(3,000²) N ≈ 1.75 × 10⁶ N = 1.75 MN. The strongest distractor is 0.18 MN, which is about ten times too small and can result from an incorrect length or unit substitution. Euler load is an ideal elastic critical value, not automatically a design resistance.
Do not treat an Euler result as a code design capacity: real design checks may require additional material, imperfection and stability provisions.
7. Bending stress in a rectangular section
This checks the elastic flexure formula for a rectangular section bending about its strong axis.
A rectangular beam section is 100 mm wide and 200 mm deep. It bends about the axis that makes the 200 mm dimension the depth. If M = 20 kN·m, what is the magnitude of the elastic stress at an extreme fibre?
For this axis, Z = bh²/6 = 100 × 200²/6 ≈ 666,667 mm³. Convert the moment to 20 × 10⁶ N·mm; σ = M/Z ≈ 30 N/mm² = 30 MPa. The strongest distractor is 60 MPa, which can result from using an incorrect section modulus or omitting the factor of 6 in the rectangular-section formula.
The depth is squared in the section modulus. Confirm which way the section bends before choosing the relevant axis.
8. Shear force at midspan under a UDL
This checks the shear-force calculation, not the bending moment. The beam and loading are as specified in the question.
A simply supported beam spans 5 m and carries a 4 kN/m UDL over the full span. What is the internal shear force at midspan?
The total load is 20 kN, so each support reaction is 10 kN. At midspan, 2.5 m of UDL to the left contributes 4 × 2.5 = 10 kN downwards. The internal shear is therefore 10 − 10 = 0 kN. The strongest distractor is 10 kN, which is the support reaction, not the shear at midspan.
A shear-force diagram for this loading changes linearly from one support to the other and crosses zero at midspan. The bending moment is largest where the shear crosses zero in this case.
9. Zero-force member at a truss joint
This checks a useful joint-equilibrium rule. It applies only if the joint has no external load or support reaction.
At a pin-jointed truss joint, two members are collinear and a third member is not collinear with them. There is no external load or support reaction at the joint. What can be concluded about the member forces?
Joint equilibrium perpendicular to the two collinear members requires the non-collinear member’s force to be zero. The strongest distractor is that the two collinear members are both zero; they may instead carry equal and opposite forces along their shared line. The rule depends on there being no external load or reaction at that joint.
Apply zero-force-member rules at the joint where their conditions hold; do not generalise them to a loaded joint.
10. Reactions for an off-centre point load
This checks equilibrium for a point load that is not at midspan.
A simply supported 6 m beam carries an 18 kN downward point load 2 m from the left support. What are the vertical reactions at the left and right supports, respectively?
Taking moments about the left support gives RB × 6 = 18 × 2, so RB = 6 kN. Vertical equilibrium then gives RA = 18 − 6 = 12 kN. The strongest distractor is 6 kN and 12 kN, which reverses the reactions: the support nearer the point load carries the larger reaction.
Turn errors into the next practice set
Classify each miss before moving on: equilibrium, choosing the right formula, unit conversion, sign convention or arithmetic. Then solve a fresh problem of the same type and explain the key step aloud. A single wrong answer may be a slip; repeated errors in the same step point to a gap worth revising.
A sample practice profile makes that review concrete:
The percentages and frequencies here describe a sample learner’s practice, not an exam’s scoring or topic weighting. Use your own results to pick the weakest topic, then revisit its assumptions and units before repeating the calculation.
If the same point is missed twice, turn it into a short retrieval prompt rather than rereading the whole solution. For example:
You lost this mark twice: for a pin-ended column using Pcr = π²EI/L², what length belongs in the formula, and what units must L and EI use together?
Answer the prompt from memory, then check that your response names the effective length implied by the stated support condition and keeps units consistent. For code-based design questions, add the required standard and clause to your own revision notes rather than assuming the same provisions apply everywhere.
How MySummaries helps
Build a revision board from your own structural engineering notes, then generate practice questions from the material you are studying. Use the marked results to identify repeated gaps and make them into cards for spaced revision. Open MySummaries.