What a structural engineering viva tests

Structural engineering viva questions can range from explaining a basic load path to defending a design choice, interpreting a failure, or describing how you would investigate an unfamiliar structure. The exact format depends on the university, qualification or professional body. There is no single international structural engineering viva syllabus or set of official marking criteria. Check the relevant institution’s or professional body’s website for its current format, assessment requirements and technical standards.

For practice, prepare to make your engineering reasoning visible. A strong answer does more than name a formula: it defines the problem, states assumptions, follows the forces through the structure, identifies relevant limit states and explains what information could change the conclusion. If you do not know a code-specific value, say so and explain how you would verify it rather than guessing.

A useful response sequence is:

  1. Clarify the problem. Identify the structure, the action or observed behaviour, and what is being asked.
  2. State assumptions. Mention the structural system, support conditions, material behaviour or other assumptions you need.
  3. Reason from mechanics. Trace the load path or describe the relevant structural behaviour.
  4. Check failure and serviceability. Name plausible failure modes and the checks that matter.
  5. Close with limits or next steps. Explain what evidence, calculation or inspection would confirm your answer.

Keep the first response concise, then develop it when the examiner asks follow-up questions. Do not recite every fact you know about a topic. Prioritise the facts that answer the question.

Set up a realistic practice viva

A viva is a conversation, so practise aloud rather than only reading notes. Ask a study partner to interrupt with questions such as “What assumption are you making?”, “What would make that unsafe?” and “How would you check that on site?” If practising alone, record your answer and listen for unexplained jumps, vague phrases and unsupported certainty.

Use diagrams when they help. A quick free-body diagram, load path sketch or moment diagram can make an answer easier to follow. Label supports, loads and the direction of forces; do not leave the examiner to infer what your drawing means.

The examiner strip below is for a structural engineering practice set, not a claim about the criteria or format of any particular institution’s viva. MySummaries gives this practice examiner an emphasis on load paths and assumptions, then on failure modes and safety.

A practice examiner strip for this subject looks like this:

ExaminerStructural Engineering viva practice
Load path and boundary conditionsAssumptions, failure modes and safety

A useful practice set should move between core principles and applied judgement. These five stations do that: each begins with an opening question, but a real examiner may take a different direction depending on your answer.

The station list for a structural engineering practice board could look like this:

StationAttemptsBestAvg
The beam with a new openingA client wants a services opening through an existing reinforced-concrete beam. How would you assess the request?37872
A slender compression memberA steel column has a high calculated axial resistance but appears slender. What do you check before accepting the design?27469
Cracking in a concrete frameA survey finds new cracks near the top of a beam at a column face. What is your initial structural assessment?0——
A transfer structureHow would you explain the design considerations for a transfer beam supporting columns above?18175
Unexpected movementA building occupant reports increasing floor vibration. How do you investigate the concern?27671

Station 1: A proposed opening in an existing beam

This station tests whether you separate an attractive design change from the checks needed to establish that it is safe. Start by clarifying the opening’s size and location, the beam span and support conditions, the loads, and whether drawings or reinforcement records are available. Do not assume the reinforcement layout from the building’s age or appearance.

A recorded practice answer to the first station could be marked like this. The scores below are MySummaries’ practice feedback, not an official exam rubric.

Oral — The beam with a new openingMarked

Examiner

A client wants a services opening through an existing reinforced-concrete beam. How would you assess the request?

2:313:00Mark answer
78%The beam with a new opening — marked78/100 · Developing · 2:31 spoken of 3:00
Problem definition and information needed19/25

You asked for the opening position and existing drawings, but did not ask whether the beam is part of a continuous frame or identify the applied loads.

ImproveEstablish the structural arrangement, span, supports, loading and proposed opening geometry before discussing a solution.

Structural reasoning and load path21/25

You recognised that the opening interrupts the concrete section and may intersect reinforcement.

ImproveExplain how the opening changes the paths for shear and bending forces, and why its position along the span matters.

Safety and verification19/25

You proposed a survey, but did not clearly say that reinforcement must be located before cutting or that capacity needs checking.

ImproveRequire a suitable reinforcement survey and a verified assessment before any alteration; address temporary works if the intervention could affect stability.

Communication and conclusion19/25

The answer was structured, but it ended without a clear decision or next step.

ImproveConclude that you would not approve cutting until the geometry, reinforcement and capacity had been verified, then state who must review the proposal.

A strong answerI would first confirm the beam’s span, supports, continuity, loading and the proposed opening’s size and position. I would obtain drawings and verify the actual reinforcement and services on site, using an appropriate survey before any cutting. The opening removes part of the section and may interrupt longitudinal reinforcement or links, so I would assess the affected bending, shear and load path rather than rely on a general rule. I would check the altered member against the applicable design basis and consider temporary works and the construction sequence. I would not authorise the opening until the assessment and any strengthening detail had been reviewed and approved.

That is a MySummaries station, filled with structural engineering material. Yours is written from your own notes. Start free

The key judgement is the sequence: establish what is there, assess what the opening changes, then decide whether a design solution is possible. Saying “add reinforcement” is not enough unless you explain what force it must transfer and how it can be anchored into the existing structure. On a real project, the applicable code, condition of the concrete and approval process must be confirmed for that jurisdiction and building.

Station 2: A slender steel column

This question checks whether you distinguish material strength from member stability. A column can have a high yield strength and still be governed by buckling. Explain which restraints and effective length assumptions you are using; do not treat an idealised calculation as proof that the real member has those restraints.

A second practice recording shows how to make that distinction explicit:

Oral — A slender compression memberMarked

Examiner

A steel column has a high calculated axial resistance but appears slender. What do you check before accepting the design?

2:443:00Mark answer
74%A slender compression member — marked74/100 · Developing · 2:44 spoken of 3:00
Problem definition and assumptions18/25

You identified the column length but did not state how you would establish its end restraint or the frame’s bracing condition.

ImproveState that effective length depends on the restraint and stability system in each direction, and verify those conditions in the structural model and details.

Structural reasoning and stability20/25

You correctly raised buckling, but focused mainly on the ideal Euler expression.

ImproveRelate slenderness, flexural stiffness and effective length to buckling, then explain that design resistance must account for imperfections and the applicable design method.

Safety and checks18/25

You mentioned axial force but did not cover eccentricity or combined actions.

ImproveCheck the governing code’s member stability method, end moments, second-order effects where relevant, cross-section classification and connection or restraint capacity.

Communication and conclusion18/25

The answer had relevant points but did not finish with a clear acceptance condition.

ImproveState that the column is acceptable only when the verified restraint model and all relevant member checks satisfy the project’s design basis.

A strong answerI would first confirm the column length, section, material, axial force, end moments and the restraints provided in both principal directions. A slender compression member may fail by instability before reaching its cross-section yield resistance, so I would verify the effective length and the stability system rather than infer them from appearance. For an ideal elastic column, the Euler critical load is proportional to EI and inversely proportional to the square of effective length, but real design also accounts for imperfections and the applicable code’s buckling method. I would check combined axial force and bending, second-order effects where required, and whether the assumed restraints are actually detailed and effective. I would accept the design only after those assumptions and checks are verified against the project’s governing standard.

The ideal pinned-column relationship is often written as Pcr = π²EI/(KL)². In a viva, it is useful to explain what the symbols mean and the limits of the ideal model: real members have imperfections, residual stresses and boundary conditions that may differ from an ideal pin. The design resistance and required checks depend on the governing standard, section and structural system, so do not quote a universal buckling reduction factor.

If challenged, explain that a restraint only counts if it can provide the required restraint and transfer the resulting forces. A modelled support that is not present in the connection or bracing details is not a reliable design assumption.

Station 3: New cracking in a concrete frame

This station tests judgement under uncertainty. A crack’s location, direction, width, change over time and relation to loading all matter. A photograph alone rarely establishes the cause. Your first task is to identify immediate risks and gather evidence, not to declare a diagnosis from one visual clue.

A third practice answer could receive feedback like this:

Oral — Cracking in a concrete frameMarked

Examiner

A survey finds new cracks near the top of a beam at a column face. What is your initial structural assessment?

2:203:00Mark answer
81%Cracking in a concrete frame — marked81/100 · Competent · 2:20 spoken of 3:00
Problem definition and evidence20/25

You asked about the crack pattern and recent changes, but could be more specific about measuring and recording the location and width.

ImproveRecord crack position, direction, length and width, compare with previous surveys, and establish when it appeared and whether it is changing.

Structural reasoning and differential causes21/25

You linked top-face cracking near a support to possible negative bending, while keeping other causes open.

ImproveSay that the pattern is a clue, not a diagnosis, and consider detailing, restraint, construction history and non-structural causes alongside structural actions.

Safety and next steps21/25

You proposed an inspection but did not state how you would respond if movement or signs of instability were found.

ImproveExplain that you would escalate promptly if there were evidence of active movement or immediate danger, and restrict access or seek urgent support where warranted.

Communication and conclusion19/25

The answer was cautious and understandable, but the investigation sequence could be clearer.

ImproveGive the steps in order: assess immediate risk, document and monitor, review design and loading information, then arrange targeted investigation.

A strong answerI would first assess whether there are signs of immediate danger, such as rapid change, significant movement or other evidence of instability, and escalate urgently if they are present. I would document the crack’s location, direction, length and width, compare it with earlier records, and find out when it appeared and whether it is progressing. Cracking near a beam-column support could be consistent with negative bending, but that is only one possibility; restraint, detailing, construction history and other causes also need consideration. I would review the drawings, reinforcement details, loading and any recent alterations, then arrange targeted inspection or monitoring as appropriate. I would not diagnose the cause or recommend a repair until the evidence and structural implications had been assessed.

A useful answer names a plausible structural interpretation without turning it into a conclusion. For example, top-face cracking near a beam support may prompt you to consider hogging moment and reinforcement detailing, but the observed pattern does not prove the cause. Ask whether loads, supports, partitions, temperature conditions or nearby work have changed. If there are signs of active movement or possible immediate danger, make the safety response explicit and follow the responsible organisation’s procedures.

The feedback wording for one phrase from this answer can be used to practise replacing a vague response with a specific one:

Transcript

I would first look at the crack and check whether it is changing. Then I would find the drawings and ask about recent changes. If it looked serious, I would get someone to inspect it. I would not decide the cause from the photograph alone.

not enough detail
If it looked serious, I would get someone to inspect it.

This recognises uncertainty, but does not say what signs make the situation urgent or what immediate action follows.

Say: Say: ‘If I found rapid crack growth, significant movement or other signs of instability, I would escalate immediately, restrict access if necessary and arrange an urgent assessment by the responsible structural engineer.’

How to use these questions in your own preparation

Repeat each station after reviewing the points you missed. Keep the opening response short enough to leave room for follow-up questions. Then practise the likely probes: What would you measure? Which assumption controls the result? What could fail first? What information would change your decision? Those questions expose gaps more clearly than repeating a memorised model answer.

Keep a record of your own recurring problems. Common ones include giving a formula without its assumptions, overlooking the load path, naming a failure mode without a check, or proposing an intervention before establishing the existing condition. Turn each specific gap into a prompt and revisit it later. For code clauses, load combinations, material properties and required professional procedures, use the applicable official standard or body guidance; they are not interchangeable across countries.

A final spoken debrief can focus on one behaviour to change next time:

Spoken feedback

You identified a plausible failure mode, but the answer needs the support assumptions before the calculation can be trusted.

How MySummaries helps

Build a revision board from your own lecture notes, design examples, standards extracts and photographed handwritten notes. From that board, MySummaries can generate oral-practice stations, record your answers, mark them against your material and turn repeated gaps into revision prompts. That lets you practise the questions your course or professional pathway actually covers, while keeping code-specific requirements tied to the sources you supplied.